IT tugi ja kaugabi ✶ IT support & remote assistance

Zebra GK & GX series label dektop printers button modes

With the printer power on and top cover closed, press and hold the Feed button for several seconds. The green status LED will flash a number of times in sequence. The explanation at the right (Action) shows what happens when you release the key after the start specific number of flashes and before the next flash sequence starts.

* Configuration Status – Prints a detailed printer configuration status label. The label can be used to verify printing, assist printer to computer communication configuration, maintenance, troubleshooting, and help us with customer care communications.
*
**
Standard Auto Media Calibration – The printer detects and sets media type and media length, and it adjusts the media sensors for optimal performance with the installed media. The printer will feed one to four labels while calibrating.
*
**
***
Serial Port Configuration – Applies only to printers with serial interface ports.
To reset the serial port communication parameters, except for Flow Control. Press and release the Feed button while the LED rapidly flashes amber and green.
*
**
***
****
Factory Defaults – Resets the printer to the factory default settings.
Some configuration settings are notreturned to their initial ‘out of box’ settings. Other settings are exclusively set, viewed and controlled by programming are also reset. The performs a standard media calibration and then a memory defragmentation routine.
Once the printer has entered the Factory Default mode, the status light will turn amber for three (3) seconds. During that time you may do two things: Do nothing and the printer will reset the factory defaults automatically as described above OR press and hold the feed button to enter a
factory default reset modes for printers with a network (Ethernet, Wi-Fi or Bluetooth) printer
option. Releasing the button after the first flash resets the network factory options only. Releasing the button after the second flash sequence (two flashes) will reset the printer defaults only. Releasing the button after the third flash sequence (three flashes) will reset both printer and network settings.
*
**
***
****
*****
Print Width Adjustment – Prints a succession of boxes starting at the minimum print width and ending in the printer’s maximum print width in 4mm increments. Press the Feed button once when the printer has reached the desired maximum print width. Note that the printer driver and applications can override this setting.
*
**
***
****
*****
******
Print Darkness (Density) Adjustment – Prints a succession of bar code simulation patterns starting at the minimum darkness (print density/heat) and ending in the printer’s maximum darkness in increments of four (4) using the ZPL darkness setting range values. Press the Feed button once the pattern is clear and legible. Do not continue to increase the darkness setting or bar code line widths may become distorted reducing readability. Note that the printer driver and applications can override this setting.
*
**
***
****
*****
******
*******
Manual Media Calibration – The printer runs extensive tests to detect and set media type and media length, and then it adjusts the media sensors for optimal performance with the installed media (equivalent ZPL command ~JG). Manual calibration is recommended whenever you are using pre-printed media, print on the liner or if the printer will not correctly auto calibrate. A graphical profile of the media sensing will print.

 

Configure ZEBRA iMZ320 to work with Android

Open Zebra Setup Utilities

Select your printer (if not already selected) from the list of printers.

Click on the Configure Printer Connectivity button.

Select Bluetooth from the options and then select Next.

Change the Enable Reconnect setting from iOS Only to Off.

If you know your printers Bluetooth settings you can fill them in here and then press Finish and then your printer will update.

If you don’t know your printers Bluetooth settings then press Next and continue with the steps in this document. Highlight the line that says

!U1 setvar “bluetooth.enable_reconnect” “off”

and with that highlighted, right-click and select Copy.

Hit Cancel so you return to the Zebra Setup Utilities window and select Open Printer Tools.

Within the Tools window select the Action tab.

From the list of commands select Send Command and press Send.

Do not paste anything in the single line input field, once your press Send Command another window will open.

With the Printer Command window open, right-click and Paste the command from before and then press the Enter key one time so the cursor should be on a new line right below the command you have pasted.

Press the Send button to send the command to the printer.

Once you Close the Tools and Close the Zebra Setup Utilities you are now ready to begin using your printer with Android devices.

Zebra Setup Utilities

Zebra label printer commands

Enable ZPL or Line Print mode on mobile printers

! U1 setvar “device.languages” “zpl”
! U1 setvar “device.languages” “line_print”
! U1 getvar “device.languages”

ZT series printer label counter

! U1 setvar “display.batch_counter” “enabled”
! U1 getvar “display.batch_counter”

Disable sleep mode on Zebra

! U1 setvar “power.sleep.enable” “off”

Wireless Zebra printer experiencing wireless connectivity issues

! U1 setvar “wlan.keep_alive.enable” “on”

Roaming reconnect (CISCO devices)

! U1 setvar “ip.roam_packet” “on”

WLAN Power save off

! U1 setvar “wlan.power_save” “off”

Complete alphabetical listing of ZPL II commands

Zebra ZT400 series

%d bloggers like this: